Cable & Wire

10 pin Test Line 350MM

$9.90 

Description:

• Length: 350mm
• Imports of wire rod
• 10 color line
• 5-color two-pin test clip
• DuPont joint and integrated sheath

Application:

• External expansion breadboard test circuit Application
• Ready-made circuit board test leads
• Plat DP1 test experiment

Breadborad jumper wire 65pcs pack

$5.0

This is approximately 65 pcs male-to-male jump wires cables 
The length of the wires : 115mm, 160mm, 200mm, 240mm

Adapter Board

$1.90

Wiichuck A Wii-Nunchuck Adapter

The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire interface of the Nunchuck are all broken out to a 4-pin 0.1 pitch header. Compared with standard WiiChuck, the DFRobot WiiChuck has extra 4 pins which allow you connect it to two devices.

The Wii Nunchuck is loaded with features -- a 2-axis joystick, two buttons and a 3 axis +-2g accelerometer -- and any device capable of I2C can communicate with it! The WiiChuck allows you to interface with the Nunchuck without making a mess and cutting the wires.

$4.50

QFN/QFP/TQFP/LQFP 16-80 to DIP Adapter

QFN/QFP/TQFP/LQFP 16-80 pins to DIP Adapter/ Breakout Board. Double side FR-4PCB design which could compatible with more QFP IC.
One side is 16-80pin to DIP at 0.5mm pitch.
The other side is 40-64pin to DIP at 0.4mm pitch and 0.65mm pitch for 80pin.

Protoboard

$0.46

Double-Sided Protoboard 2cm x 8xm

FEATURES:

Pads on Double-sided

No odor

Finely drilled

Tough

Including power pad

Clean hole

Points:6x28

$0.60

Double-Sided Protoboard 3cm x 7cm

FEATURES:

Pads on Double-sided

No odor

Finely drilled

Tough

Including power pad

Clean hole

Points:10x24

Breadboard

Magic Breadboard Mama Boart

This Magic Breadboard Assembly kits could assemble with many of super-mini-breadboards. The super-mini-breadboard is smaller than before mini breadboard. It's material savings and free combination. You just need connect the super-mini-breadboard each other by Breadborad jumper wire . 

Note: this board not include the super-mini-breadboard.

The super-mini-breadboard size is 15mm x 20mm and has 25 holes. The there are two feet could plugin Magic Breadboard Mama Boart.

The Magic Breadboard Mama Boart size is 132mm x 92mm. 

There are many color of super-mini-breadboard for your choosing.It could clearly provide teaching schematic diagram.

Magic Super-Mini-Breadboard Black

The super-mini-breadboard size is 15mm x 20mm and has 25 holes. The there are two feet could plugin Magic Breadboard Mama Boart.

Prototyping

Breadboard

Protoboard

Adapter Board

Cable & Wire

RepRap MeLzi

A compact all-in-one controller board for RepRaps with one extruder head, optimized for mass production.

The point of RepRap is to make itself, of course. But sometimes people just want plug-and-play RepRap electronics so they can concentrate on the other aspects of the machine, or just because they are more software or mechanics oriented than electronics oriented.

Melzi is designed to be a complete set of RepRap electronics that should be very cheap to mass produce. It was originally based on the Arduino Leonardo (Francesco Melzi was Leonardo's pupil).

Specification:

• Processor: ATMEGA1284P
• All screw connectors - no soldering
• Micro SD card slot for GCode files
• Mini USB interface
• 4 x A4988 stepper drivers
• 3 x MOSFET drivers for hot end, bed and cooling fan
• Dimensions: 210mm x 50mm x 17mm
• Weight: 70g

RAMPS Mega Shield V1.4 RAMPSHD

RepRap Arduino Mega Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. It is a "1.5 layer" designed board (i.e. it's double sided board, but one of layers can easily be replaced with wire-jumpers) that is printable on your RepRap with the etch resist pen method, or home fabbed with toner transfer. At the same time it is based on the powerful Freaduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally as long as the main RAMPS board is kept to the top of the stack a number of Arduino expansion boards can be added to the system. 

REMPS LUXURY Kit

Highly recommended,in order to easily and quickly build your own 3D printer, we provide more convenient combination kit 3D printer luxury suite with the support the Max 2A current ElecFreaks Mega2560. 

To match Endstop SDramps rich packages quickly. With more 4GB SDcard, Smart LCD controller, smart adapter and 20X4 character LCD display operation interface, and MK2a PCB heatbed.

The LUXURY Kit include :

1 x Freaduino Mega2560 (Max support 2A)

1 x Ramps Shield v1.4

5 x A4988 stepstick

5 x Heatsink

1 x Heat sticker

2 x Heat grease

1 x Grease brush

3 x Endstop

1 x SDramps

1 x LCD Smart Controller board

2 x 30cm cables

1 x Smart Adapter

1 x Characters LCD2004

1 x 4GB SanDisk SDcard

1 x PCB heatbed MK2a(include 1k resistor and 2 LED)

2 x Plastic box

Prusa i3 Full Kit - EBoti3

EBoti3 was designed base on Prusa i3 and we modified the Extruder. Its a full kit and easily built.

Include:

1 x Prusa i3 Full Kit - EBoti3

1 x Tools kit

1 x CD (All Documentation/User Guide/Vedios In)

Parameter：

Size	200 * 200 * 180mm
Power Supply	110V/220V
Power Plug	EU plug and U.S plug
Thickness	0.1-0 .4 mm
SD card offline print	Support
LCD	None
Maximum print speed	100mm / s
Nozzle diameter	0.4mm standard
XY axis positioning accuracy	0.012mm
Z-axis positioning accuracy	0.004mm
Support materials	ABS, PLA
Material Diameter	1.75mm, 3mm
Consumables tendentious	PLA
Language	Chinese / English
Supported file formats	STL, G-Code
Model support functions	generation / non-generation alternative
Machine size	430 * 405 * 370mm
Weight	6.7kg
Package size	400 * 350 * 300mm
Package Weight	400 * 350 * 300mm
Operating System	XP, WIN7 32 bit
PC software	Replicotor-Host
Environmental requirements	10-30 ℃, humidity of 20-50%

Read more: http://www.elecfreaks.com/store/prusa-i3-full-kit-eboti3-p-763.html#ixzz3IBLWkN4F

ElecFreaks PCB Service

As an electronic hobbyist, are you still bored for expensive PCB production fee. Don't worry, the ElecFreaks PCB service may help you solve this problem.

Our Printed circuit board / PCB Service is available now. Let me have a brief introduction to you. The Fusion PCB Service starts from $9.9. In order to meet various requirements, we provide 3 kinds of services as below:

In the first service ‘2 Layer 10cm*10cm max -10pcs’, you can chose 3 kinds of PCB dimension(5cm X 5cm Max, 5cm X 10cm Max, 10cm X 10cm Max.

The second service ‘2 Layer 20cm*20cm Max (5PCS or 10PCS optional)’ provides more PCB dimensions.

The third service ‘2 Layer 20cm*20cm max - 50PCS’ is targeted at small batch requirement.

 

1. 2 Layer 10cm*10cm max - 10pcs  start at $9.9 
2. 2 Layer 20cm*20cm max - 50pcs  start at $9.9
3. 4 Layer 5cm*5cm max - 10pcs  start at $65.0
4. 4 Layer 10cm*10cm max - 10pcs  start at $99.0